DIT-5200 Data Sheet.pdf

 

 

 

 

 

 

DIT-5200 User Manual

 

 

 

 

 

 

Electronics	IGS format	STEP format
DIT-5200	IGS	STEP

Sensor	IGS format	STEP format
15N sensor	IGS	STEP
20N sensor	IGS	STEP

 

Target material	Aluminum
Output voltage	±10 volts typical
Power dissipation	At 15N sensor head <0.5 mW/sensor typical At 20N sensor head <2 mW/sensor typical Electronics <1.35 Watts
Frequency response	0-20 kHz
Input voltage	±15 volts
Output impedance	<1 Ohm
Weight	Electronics 6 oz. W/4 15N sensors 8 oz.
Operating temperature range	Electronics +32°F to +140°F (0°C to +60°C) Sensors -62°F to +220°F (-52°C to +105°C)
Storage temperature range	Electronics -26°F to +180°F (-32°C to +82°C) Sensors -62°F to +220°F (-52°C to +105°C)

 

KAMAN DIT-5200 SENSORS

Sensor click to view	Range ±mil/±mm	Null mil/mm	Typical Non- Linearity ± %FR	Maximum Non- Linearity ±%FR	Typical Sensor TempCo ± %FR/°C	Resolution p-p%FR at 1 kHz BW at FR	Resolution p-p%FR at 1 kHz BW at Null
15N	10/0.25	15/0.38	0.15%	0.30%	0.02%	0.015%	0.004%
15N	20/0.51	25/0.64	0.25%	0.50%	0.03%	0.008%	0.002%
15N	35/0.89	40/1.02	0.50%	1.00%	0.03%	0.005%	0.003%
20N	10/0.25	20/0.51	0.10%	0.20%	0.02%	0.025%	0.005%
20N	20/0.51	40/1.02	0.15%	0.30%	0.02%	0.015%	0.005%
20N	50/1.27	60/1.52	0.25%	0.50%	0.03%	0.008%	0.003%
20N	75/1.91	85/2.16	0.50%	1.00%	0.03%	0.005%	0.002%

Note:
Full range (FR) is considered as twice the ±range value. Temperature coefficient at null <0.005% FR/°C typical. Performance specifications are based on aluminum target.

 

Many options are available to customize a standard system to meet the exact needs of the application. The most popular are:

Sensor Cables

Sensor cable extension
Most sensors can handle longer cable lengths, although increasing the cable length can and will affect some performance specifications. Shorter than standard cable lengths are also available. Call an apps engineer to discuss your particular requirements.

In-line cable connector splice
Many sensors come with integral sensor cables. Routing this cable in some applications is difficult and something you only want to do once. Including an in-line connector splice in the cable, near the sensor itself, allows for easy sensor replacement should the need arise.

Hermetic in-line connector splice
Some applications pass the sensor through a pressure boundary, most commonly a vacuum chamber wall. We offer an in-line hermetic bulkhead splice for these applications.

Special Calibrations

Range
Standard published ranges are based on meeting a set of performance specs. Custom calibrations are possible to meet specific application needs. Contact a Kaman applications engineer if a custom calibration is desired.

Target material
Unless otherwise specified, nonferrous systems will be calibrated with an aluminum target. If your target material is significantly different in conductivity and/or permeability it may be best to calibrate using the same material as your target.

 

Kaman Accessories data sheet.pdf

 

 

 

 

 

Kaman Accessories data sheet.pdf