KD-2306 Data Sheet.pdf

 

 

 

 

 

 

KD-2306 User Manual

 

 

 

 

 

 

Electronics	IGS format	STEP format
KD-2306	IGS	STEP

Sensor	IGS format	STEP format
.5SU sensor	IGS	STEP
.5SUM sensor	IGS	STEP
1S sensor	IGS	STEP
1SM sensor	IGS	STEP
1U1 sensor	IGS	STEP
1SU sensor	IGS	STEP
1SUM sensor	IGS	STEP
2S1 sensor	IGS	STEP
2UB1 sensor	IGS	STEP
2S sensor	IGS	STEP
3U1 sensor	IGS	STEP
4S1 sensor	IGS	STEP
4SB sensor	IGS	STEP
6U1 sensor	IGS	STEP
6C sensor	IGS	STEP
8C sensor	IGS	STEP
15U1 sensor	IGS	STEP
10C sensor	IGS	STEP
10CU sensor	IGS	STEP
30U1 sensor	IGS	STEP
12CU sensor	IGS	STEP
60U1 sensor	IGS	STEP
1UEP sensor	IGS	STEP
2SMT sensor	IGS	STEP
9U sensor	IGS	STEP
12U sensor	IGS	STEP
16U sensor	IGS	STEP
26U sensor	IGS	STEP
38U sensor	IGS	STEP
51U sensor	IGS	STEP

 

The following specifications can be applied to the full range of systems using standard sensor
options in the sensors chart. Each sensor has specific performance specifications that
can be better than those listed below.

Resolution	0.01%FS
Frequency response	50KHz (-3dB point) Higher response available on request.
Nonlinearity	<1%FS
Thermal sensitivity	Standard 0.1%FS/°F; compensated 0.02%FS/°F
Output options	0-10 VDC (standard); 0-5 VDC ±5 VDC, 4-20 mA
Operating temperature range	Electronics +32°F to +132°F (0°C to +55°C)
Storage temperature range	Electronics -67°F to +220°F (-55°C to +105°C)
Power supply requirements	Voltage +15 to +30 Vdc Voltage regulation ±1/2 Vdc Current 150 mA

 

STANDARD TEMPERATURE SENSORS
– 67° TO +220° F (–55° TO +105° C)

SENSOR click to view	STANDARD MEASURING RANGE		TARGET MATERIAL		STATIC RESOLUTION
	inch	mm	non-fer	ferrous	μ in	μ m
.5SU / .5SUM	0.020	0.5	.5SU	.5SUM	4	0.1
1S /1SM	0.040	1.0	1S	1SM	4	0.1
1U1	0.040	1.0	•		4	0.1
1SU / 1SUM	0.050	1.3	1SU	1SUM	5	0.1
2S1	0.080	2.0	•		8	0.2
2UB1	0.080	2.0	•		8	0.2
2S	0.100	2.5	•	•	10	0.3
3U1	0.120	3.0	•		12	0.3
4S1	0.160	4.0	•	•	16	0.4
4SB	0.160	4.0	•		16	0.4
6U1	0.240	6.0	•	•	24	0.6
6C	0.250	6.4	•	•	25	0.6
8C	0.500	13	•	•	50	1.3
15U1	0.600	15	•		60	0.2
10C	0.750	20	•	•	75	2.0
10CU	1.000	25	•	•	100	2.5
30U1	1.200	30	•	•	120	3.0
12CU	2.000	50	•	•	200	5.0
60U1	2.400	60	•	•	240	6.0

MODERATE TEMPERATURE SENSORS:
CRYOGENIC TO +400° F (+200° C), SENSOR DEPENDENT

SENSOR click to view	STANDARD MEASURING RANGE		TARGET MATERIAL		STATIC RESOLUTION
	inch	mm	non-fer	ferrous	μ in	μ m
1UEP	0.040	1.0	•	•	4	0.1
2SMT	0.100	2.5	•	•	10	0.3
6CMT	0.250	6.4	•	•	25	0.6
8CMT	0.500	13	•	•	50	1.3
9U	0.160	4.0	•	•	16	0.4
12U	0.200	5.0	•	•	20	0.5
16U	0.320	8.0	•	•	32	0.8
26U	0.500	12	•	•	50	1.2
38U	0.750	20	•	•	75	2.0
51U	1.000	25	•	•	100	2.5

 

DECLARATION OF CONFORMITY

Model Number
KD-2306 non-contact linear proximity/displacement measuring system

Manufacturer
Kaman Precision Products
Measuring & Memory Systems
217 Smith Street
Middletown, CT 06457
USA
Telephone 860-632-1000
Fax 860-632-4515

Conforms with Applicable Standards of:
Council Directive 89/336/EEC as amended by Council Directive 92/31/EEC (EMC Directive)
Council Directive 73/23/EEC as amended by Council Directive 93/68/EEC (LVD Directive)

EMC
EN 61326-1:2006 - Industrial Electrical equipment for Measurement, Control and Laboratory Use – EMC

EN 55011:2007 – Class A Group 1 Radiated Emissions Requirements

LVD
EN 61010-1:2001 The KD-2306 unit requires the use of a limited energy power supply circuit per EN 61010-1:2001 Article 9.3. The KD-2306 does not use or switch voltages in excess of 60 VDC or 42.4 VAC peak (30 VAC rms).

 

Many options are available to customize a standard system to meet the exact needs of the application. The most popular are:

Sensor Cables

Sensor cable extension
Most sensors can handle longer cable lengths, although increasing the cable length can and will affect some performance specifications. Shorter than standard cable lengths are also available. Call an apps engineer to discuss your particular requirements.

In-line cable connector splice
Many sensors come with integral sensor cables. Routing this cable in some applications is difficult and something you only want to do once. Including an in-line connector splice in the cable, near the sensor itself, allows for easy sensor replacement should the need arise.

Hermetic in-line connector splice
Some applications pass the sensor through a pressure boundary, most commonly a vacuum chamber wall. We offer an in-line hermetic bulkhead splice for these applications.

Special Calibrations

Range
Standard published ranges are based on meeting a set of performance specs. Custom calibrations are possible to meet specific application needs. Contact a Kaman applications engineer if a custom calibration is desired.

Target material
Unless otherwise specified, nonferrous systems will be calibrated with an aluminum target, ferrous systems will be calibrated with a 4130 steel target. If your target material is significantly different in conductivity and/or permeability it may be best to calibrate using the same material as your target.

Temperature compensation
When the standard thermal sensitivity of 0.1%FS/°F is not enough, a temperature compensated calibration can be performed that will improve the thermal sensitivity to 0.02%FS/°F. This is accomplished over a customer specified 100°F range with the upper limit of that range <150°F. Larger ranges and higher temperatures are also possible on a best effort basis.

Output
Besides the standard 0-10VDC output, the KD-2306 offers a 4-20mA output and a differential 0-10VDC output.

Synchronization
When multiple channels are used in such a way that the sensors themselves are in close proximity to each other (within 3 sensor diameters), synchronizing the oscillators of the electronics modules will eliminate the resulting beat note interference that will be seen as noise on the outputs.

Log Amp Bypass
When extremely short range calibrations are required/desired, bypassing the log amplifier reduces noise improving performance.

 

Kaman Accessories data sheet.pdf