KD-5100 Data Sheet.pdf

 

 

 

 

 

 

KD-5100 User Manual

 

 

 

 

 

 

Electronics	IGS format	STEP format
KD-5100	IGS	STEP

Sensor	IGS format	STEP format
15N sensor	IGS	STEP
20N sensor	IGS	STEP

 

FOR AN ALUMINUM TARGET

Nonlinearity	±0.1% to ±0.5% FSO; application dependent.
Output	±10 Vdc maximum
Long-term stability	(nominal; stabilized at 70°F [21°C] scale factor dependent) 5 x 10-6 inches/month (1.27 x 10-4 mm/month)
Thermal sensitivity	at null; application dependent; <5 mV per °F.
Frequency response	22 kHz ±5% @ 3 db
RMS input displacement resolution	(if bandwidth limited to 5 kHz): 4x10-9 x √bandwidth in Hz = in. 1x10-7 x √bandwidth in Hz = mm
Input voltage	±15 Vdc @ 55 mA typical
Power consumption	<2 watts - system
Power dissipation	<0.5 mW per 15N sensor <1.5 mW per 20N sensor
Output characteristics	<5 W @ 5 mA
Operating temperature range Electronics Sensors Cryogenic 20N sensor	-4°F to +140°F (-20°C to +60°C) 62°F to +220°F (-52°C to +105°C) +4°K to +220°F (+105°C)
Storage temperature range Electronics Sensors Cryogenic 20N sensor	26°F to +180°F (-32°C to +82°C) -62°F to +220°F (-52°C to +105°C) +4°K to +220°F (+105°C)
Weight (with 5-foot cable) Electronics 15N-001 sensor 20N sensor	2.5 ounces (70 grams) 0.61 ounces (17.3 grams) 0.59 ounces (16.8 grams)

 

KD-5100 SPECIFICATIONS
FOR AN ALUMINUM TARGET

				RESOLUTION
SENSOR click to view	MAX RANGE ±inch/±mm	TYPICAL NULL inch/mm	STATIC inch/mm	1KHz inch/mm	5KHz inch/mm
15N	±0.035/±0.89	0.045/1.14	4x10-9/1x10-7	1.3x10-7/3.3x10-6	2.8x10-7/7.2x10-6
20N	±0.075/±1.27	0.090/2.29	4x10-9/1x10-7	1.3x10-7/3.3x10-6	2.8x10-7/7.2x10-6

 

 

Many options are available to customize a standard system to meet the exact needs of the application. The most popular are:

Sensor Cables

Sensor cable extension
Most sensors can handle longer cable lengths, although increasing the cable length can and will affect some performance specifications. Shorter than standard cable lengths are also available. Call an apps engineer to discuss your particular requirements.

In-line cable connector splice
Many sensors come with integral sensor cables. Routing this cable in some applications is difficult and something you only want to do once. Including an in-line connector splice in the cable, near the sensor itself, allows for easy sensor replacement should the need arise.

Hermetic in-line connector splice
Some applications pass the sensor through a pressure boundary, most commonly a vacuum chamber wall. We offer an in-line hermetic bulkhead splice for these applications.

Special Calibrations

Range
Standard published ranges are based on meeting a set of performance specs. Custom calibrations are possible to meet specific application needs. Contact a Kaman applications engineer if a custom calibration is desired.

Target material
Unless otherwise specified, nonferrous systems will be calibrated with an aluminum target. If your target material is significantly different in conductivity and/or permeability it may be best to calibrate using the same material as your target.

 

Kaman Accessories data sheet.pdf

 

 

 

 

Kaman Accessories data sheet.pdf